مشكلة ف ZBrush ver3.5 R3

[mega man]

بعد تنصيب البرنامج و تفعيل البرنامج لا أستطيع القيام بأى عملية (حفظ,فتح,تصدير...)
وتظهر رسالة تقول
Internal Error . system cpp Line:250


sorry ZBrush is unable to properly complete this function
فما الخطأ و ما الحل

[bannino]

السلام عليكم

حتى اللآن و حسب علمى لأ يوجد كراك سليم تماما للزى zbrush 3.5 R3 و الطريقة الوحيدة التى جربتها و افلحت هى الطريقة الاتية و التى انقلها من موقع gfxnews.com
How to Activate Zbrush 3.5 R3 without using a cracked exe.


Introduction:
------------------------------------------------------------------------------------------

First off, Thank you Nezumi. Your instructions are the basis for these steps.

I have simply rewritten them, trying to be as clear as possible.



Section 1: Installation Procedures. (DO NOT SKIP TO SECTION 2)
------------------------------------------------------------------------------------------

1. If you have ZBrush 3.5 R2 installed, you must first Deactivate it!

To Deactivate ZBrush 3.5 R2:

- Launch ZBrush 3.5 R2 As Administrator
- On the main Menu click Zplugin > Deactivation. Choose "Manual Deactivation"

2. Install ZBrush 3.5 R3 Without Plugins:

- Choose Custom and uncheck "Plugins"

3. Go to: \Pixologic\ZBrush 3.5 R3\

- Rename: "ZBrush.exe" to "ZBrush.R3"


4. Go to: \Pixologic\ZBrush 3.5 R3\ZData\ZPlugs\SplashData\

- Rename: "SplashNS.zsc" to "SplashNS.zsc.R3"



Section 2: Activation Procedures.
------------------------------------------------------------------------------------------

* Now you are ready to begin the activation process. To do so, you will need the following files:

ZBrush.exe (v3.5 R2 original exe)
SplashNS.zsc (v3.5 R2 Keygen)

* Note: "original exe" means the non cracked exe from pixologic's original R2 install files.

1. Copy "ZBrush.exe" (v3.5 R2 Original exe) to: \Pixologic\ZBrush 3.5 R3\

2. Copy "SplashNS.zsc" (v3.5 R2 Keygen) to: \Pixologic\ZBrush 3.5 R3\ZData\ZPlugs\SplashData\

3. Run as Administrator: \Pixologic\ZBrush 3.5 R3\ZBrush.exe

4. Click Enter Activation Code (DO NOT CLICK "OK" AFTER CODE IS DISPLAYED!!!)

5. Copy the Code and click cancel.

6. Exist ZBrush

7. Go to: \Pixologic\ZBrush 3.5 R3\ZData\ZPlugs\SplashData\

- Delete: "SplashNS.zsc" (v3.5 R2 Keygen)
- Rename: "SplashNS.zsc.R3" to "SplashNS.zsc"

8. Run as Administrator: \Pixologic\ZBrush 3.5 R3\ZBrush.exe

9. Click Enter Activation Code and Paste the Code you copied earlier (during step 5)

10. Click OK to activate.

11. Exit ZBrush

12. Go to: \Pixologic\ZBrush 3.5 R3\

- Delete: "ZBrush.exe"
- Rename: "ZBrush.R3" to "ZBrush.exe"

13. ZBrush 3.5 R3 is now activated.



Section 3: Manually Install Plugins.
------------------------------------------------------------------------------------------

The plugins are supplied in zip format and are located in the plugins folder.

1. Unzip all plugins to: \Pixologic\ZBrush 3.5 R3\ZData\ZPlugs

The End.
if you get the activation screen back when you switch to r3:
overwrite with r2 exe, launch, close, overwrite with r3 exe and launch again. If not repeat one more time, worked for me

[bizzar]

هذاا وبن اتممت تحميل الزيبراش من ..................
http://forums.cgway.net/cg27188/