السلام عليكم حاولت اتعلم تجميل نص معين اريد تعلم طرق مختلفة اخترت درس بسيط لتطبيقه
ولكن واجهتني مشكلة بعد رسم الباث للكلمة ..سأذكر أهم النقاط حتى تفيدوني ...
الدرس باللغة الإنجليزية ولكن حاولت قدر المستطاع....
رابط الدرس
حسنا أنا متوقفة الان عند الخطوة 12 ...حيث يجب ان يظهر الحرف بشكل العشب ...
لا أعرف اين أخطأت بالضبط...هل كان يجب أن أرسم الباث على العشب بصفحة أخرى غير الخلفية التي أعمل عليها ...؟؟؟؟؟؟؟!!!!!!!!!!
لأن الباث لم يظهر كما هو في الصورة....أم هل هناك طريقة أخرى ؟
أرجو ذكر أين اخطات حتى لا يتكرر معي ذلك ....
وأرجو أن اجد من يدلني على الطريقة الصحيحة....
شاكرة تعاون الجميع
ولكن واجهتني مشكلة بعد رسم الباث للكلمة ..سأذكر أهم النقاط حتى تفيدوني ...
الدرس باللغة الإنجليزية ولكن حاولت قدر المستطاع....
Step 10
OK, so here’s the text on top of the grass we got earlier.
Now a bit of planning! To make text out of grass, it’s not going to be enough just to stencil out the grass. Rather we need it to look all rough, with bits of grass sticking out the edges. To do that, we’re going to use the letter shapes as a rough guide and then trace roughly around them and periodically jut out to trace around blades of grass.
OK, so here’s the text on top of the grass we got earlier.
Now a bit of planning! To make text out of grass, it’s not going to be enough just to stencil out the grass. Rather we need it to look all rough, with bits of grass sticking out the edges. To do that, we’re going to use the letter shapes as a rough guide and then trace roughly around them and periodically jut out to trace around blades of grass.
Step 11
OK, so here we are tracing. You should use the Pen Tool (P) and frankly, if you’re not handy with it before you start, you will be by the end!
Notice how in the parts where my path juts out, it sort of follows individual blades of grass. That way when you have the final cut-out they will look like pieces of grass sticking out.
OK, so here we are tracing. You should use the Pen Tool (P) and frankly, if you’re not handy with it before you start, you will be by the end!
Notice how in the parts where my path juts out, it sort of follows individual blades of grass. That way when you have the final cut-out they will look like pieces of grass sticking out.
Step 12
When you’ve finished your path, it’s best to save it in the Paths Palette. You can do this by switching to that palette and then clicking the little down arrow and choosing Save Path. That way if you need the path again later, you can grab it.
Anyhow, double-click the path to get the selection and go back to your grass layer. Duplicate the grass layer so you still have more grass for the other letters, then invert your selection (Ctrl+Shift+I) and cut away the excess grass. In the screenshot I’ve faded back the duplicate grass layer so you can see the cut out "E" part.
When you’ve finished your path, it’s best to save it in the Paths Palette. You can do this by switching to that palette and then clicking the little down arrow and choosing Save Path. That way if you need the path again later, you can grab it.
Anyhow, double-click the path to get the selection and go back to your grass layer. Duplicate the grass layer so you still have more grass for the other letters, then invert your selection (Ctrl+Shift+I) and cut away the excess grass. In the screenshot I’ve faded back the duplicate grass layer so you can see the cut out "E" part.
Step 13
OK, so here we have our "E" on the final bakcground. As you can see, it looks only slightly better than if we’d just used the letter to stencil out the grass without bothering to trace. But that’s OK, what it needs is a bit more depth. After all, if that letter was really sitting there, we should see some shadow and sides to it.
OK, so here we have our "E" on the final bakcground. As you can see, it looks only slightly better than if we’d just used the letter to stencil out the grass without bothering to trace. But that’s OK, what it needs is a bit more depth. After all, if that letter was really sitting there, we should see some shadow and sides to it.
رابط الدرس
حسنا أنا متوقفة الان عند الخطوة 12 ...حيث يجب ان يظهر الحرف بشكل العشب ...
لا أعرف اين أخطأت بالضبط...هل كان يجب أن أرسم الباث على العشب بصفحة أخرى غير الخلفية التي أعمل عليها ...؟؟؟؟؟؟؟!!!!!!!!!!
لأن الباث لم يظهر كما هو في الصورة....أم هل هناك طريقة أخرى ؟
أرجو ذكر أين اخطات حتى لا يتكرر معي ذلك ....
وأرجو أن اجد من يدلني على الطريقة الصحيحة....
شاكرة تعاون الجميع
تعليق