; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Dec 11 2018 13:08:00 GMT+0300 (Arabian Standard Time)

; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves

; Network
M550 P"My Printer"                       ; Set machine name
M552 S1                                  ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet

; Drives
; M569 P0 S0                               ; Drive 0 goes forwards=0 BACKWARD = 1 0==Z_1
M569 P1 S1                               ; Drive 1 goes forwards=0 BACKWARD = 1 1==Z_2
M569 P2 S1                              ; Drive 2 goes forwards=0 BACKWARD = 1 NONe
M569 P3 S1                              ; Drive 3 goes forwards=0 BACKWARD = 1 3==E
M569 P4 S1
M569 P5 R1 T2.5:2.5:5:0
M569 P6 R1 T2.5:2.5:5:0
M569 P7 R1 T2.5:2.5:5:0
M569 P8 R1 T2.5:2.5:5:0

M584 X7 Y8 Z 1:2

3M350 X16Y16 Z16 U16 E16 I1                  ; Configure microstepping with interpolation
M92 X326 Y265  Z396.03 U Z396.03 E397     ; Set steps per mm
M566 X400.00 Y400.00 Z12.00 U12.00 E420.00      ; Set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z1000.00U1000 E100.00    ; Set maximum speeds (mm/min)
M201 X50.00 Y50.00 Z20.00 U20.00 E20.00     ; Set accelerations (mm/s^2)
M906 X1800.00 Y1800.00 Z1800.00 U1800.00 E1000.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                         ; Set axis minima
M208 X475 Y265 Z670 S0                   ; Set axis maxima

; Endstops
M574 X2 Y2 Z2 S0                         ; Set active LOW =0  ACTIVE HIGH = 1 endstops
M581 E0 T1 S0                            ;T1 paused the print  when it's print and T0 make emergency stop  S LOW =0  ACTIVE HIGH = 1 E for port 


; Z-Probe
M558 P5 H4 F250 T6000                   ; Set Z probe type to switch and the dive height + speeds
G31 P495 X0 Y0 Z -0.856  ; Set Z probe trigger value, offset and trigger height
M557 X50:300 Y50:195 S20                 ; Define mesh grid

; Heaters
M305 P0 x200              ; Set thermistor + ADC parameters for heater 1
M143 H0 S120                             ; Set temperature limit for heater 1 to 280C
M305 P1 T100000 B4138 R4700              ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                             ; Set temperature limit for heater 1 to 280C

M305 P102 X201 S"bed_1"
M140 P102 H2 S120

; Fans
M106 P0 S500 I0 F500 H-1                 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                            ; Define tool 0
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured